微機控制電壓擊穿測試儀 計算機系統及軟件包
1、試驗軟件是我公司最新研發的功能強大、操作簡單、顯示直觀的試驗軟件系統;
2、采用計算機控制通過人機對話方式,完成對絕緣介質工頻電壓擊穿,工頻耐壓試驗;
3、在試驗過程中可對升壓擊穿過程繪制實時曲線,每次試驗的升壓曲線都由不同顏色構成,試驗結束后可疊加對比材料的試驗數據重復性;
4、可以隨時調取當前及歷史試驗數據進行查看,編輯及修改參數;
5、試驗過程中可以隨時修改試驗條件及存儲路徑及自動存儲試驗結果;
6、試驗過程中,可隨時通過軟件決定本次試驗是否有效,方便篩選試驗結果;
7、可設置操作口令,做到專機專人操作,避免無關人員誤操作;
8、試驗報告格式靈活可變,適用于不同用戶的不同需求;
9、可對一組試驗中曲線數據的有效與否進行人為選定;
10、試驗結果數據可導入EXECL,WORD文檔編輯;
11、過電流保護裝置有足夠的靈敏度,能夠保證試樣擊穿時在0.1S內切斷電源;
12、儀器運行的持久性: 儀器可連續運行使用,不需為保護儀器而定期停機;
微機控制電壓擊穿測試儀 產品特點:
1、采用智能集成電路進行勻速升壓。
2、支持短時間內短路試驗要求。
3、電壓試驗精度: ≤ 1%。
4、試驗電壓連續可調: 0--50KV。
5、電流可采集到mA級。
6、出具國家一級計量單位校準檢定證書或出具客戶指定計量單位的證書。
7、電源:220V?10%的單相交流電壓和50Hz?1%的頻率。
8、電流電壓穩定度: 外界電源電壓波動10%時
注意事項:
本儀器為高壓試驗設備,使用時必須注意以下幾點
1、儀器安裝時應具有獨立的接地線。
2、在開機前,操作者要首先熟悉操作方法。
3、儀器不能在有強烈腐蝕性氣體及有顆粒雜質的氣體環境中使用。
4、試驗環境溫度15度到25度之間,相對濕度60%到70%之間
5、試樣擊穿瞬間有火花產生并伴有聲響,屬正常現象。
6、每次更換試樣或接觸高壓電極時必須用高壓放電棒對高壓電極進行放電,放電時間5秒以上。
7、每次進行試驗前,必須檢查儀器接地。
技術要求:
序號 | 項目 | 參數 |
1 | 設備輸入電壓 | 交流 50KV |
2 | 試驗電壓方式 | 交流 0--50 KV ;直流 0--20 KV |
3 | 電器容量 | 3KVA |
4 | 試驗方法 | 0-50KV全量程可調 |
5 | 擊穿及耐壓試驗升壓速率 | 0.1 KV/S-3.0 KV/S可調 |
6 | 試驗方式 | 直流試驗 交流試驗 |
7 | 漏電電流選擇 | 1—100 mA |
8 | 電壓測量誤差 | ≤ 1% |
9 | 試驗電壓連續可調 | 0-50 KV |
10 | 耐壓時間設定 | 0-6小時 |
11 | 九級安全防護措施 | (1) 超壓保護 |
12 |
| (2)試驗過流保護 |
13 |
| (3)試驗短路保護 |
14 |
| (4)安全門開啟保護 |
15 |
| (5)軟件誤操作保護 |
16 |
| (6)零電壓復位保護 |
17 |
| (7)試驗結束放電保護 |
18 |
| (8)獨立保護接地 |
19 |
| (9)試驗完成后電磁放電 |
主要配置:
1、試驗主機一臺 2、5萬伏高壓發生器一臺 3、全自動微電腦電壓調壓裝置一套(串口方式) 4、試驗電極規格(紫銅) 5、試驗用油盒一只:材質為有機玻璃
6、電磁自動放電裝置一套。7、電壓擊穿計算機測控軟件一套
8、計算機一套(專用抗強干擾計算機) 9、彩色噴墨打印機一臺(惠普品牌)
10、國家一級計量鑒定質檢份 11、產品使用說明書一份 12、合格證一份
整機組成:
升壓部件:由調壓器和高壓變壓器組成0~50KV的升壓部分。動部件:由步進電機均勻調節調壓器使加給高壓變壓器的電壓變化。檢測部件:由集成電路組成的測量電路。通過信號線把檢測的模擬信號和開關信號傳給計算機。計算機軟件:通過智能電路把由檢測設備采集的測控信號傳給計算機。計算機根據采集的信息控制設備運行并處理試驗結果。試驗電極:根據國家標準(1408.1-2006)隨設備提供三個電極,具體規格為:Ф25mm?25mm兩個;Ф75mm?25mm一個。(訂做除外)
交直流實驗的切換
1)本儀器高壓輸出為交流電壓。直流的獲得方式為在原回路中串入高壓硅堆,使測試回路為脈動的直流電壓。實現的過程為:硅堆已經在高壓變壓器的高壓絕緣塔中,平時用一個短路桿把高壓硅堆短接。需要直流試驗時,取出短路桿,使高壓硅堆接入測試電路中,這時回路的電壓為脈動的直流電壓。
2)前面板直流交流選擇按鈕。該按鈕的狀態不能改變?cè)O(shè)備輸出的電壓性質。按下該按鈕,設備僅僅是把直流報警電路接入。指示用戶,當打開箱門時,您需要對高壓均壓球放電。轉動放電桿,使放電桿的端部銅球接觸高壓均壓球。建議用戶每次放電銅球接觸高壓均壓球時間大于五秒。
3)試驗的交直流電壓切換,主要取決于高壓絕緣塔中的短路桿是否取出。當取出短路桿時,高壓均壓球上的電壓為直流電壓,插入短路桿時,高壓均壓球上的電壓為交流電壓。短路桿的取出、插入?yún)⒖醋髠?cè)的示意圖。
注意事項:
本儀器為高壓試驗設備,使用時必須注意以下幾點
1、儀器安裝時應具有獨立的接地線。
2、在開機前,操作者要首先熟悉操作方法。
3、儀器不能在有強烈腐蝕性氣體及有顆粒雜質的氣體環境中使用。
4、試驗環境溫度15度到25度之間,相對濕度60%到70%之間
5、試樣擊穿瞬間有火花產生并伴有聲響,屬正常現象。
6、每次更換試樣或接觸高壓電極時必須用高壓放電棒對高壓電極進行放電,放電時間5秒以上。
7、每次進行試驗前,必須檢查儀器接地。
Main configuration:
1. One test host 2. One 50000 V high voltage generator 3. One set of automatic microcomputer voltage regulator (serial port mode) 4. Test electrode specification (red copper) 5. One test oil box: made of plexiglass
6. One set of electromagnetic automatic discharge device. 7. A set of computer measurement and control software for voltage breakdown
8. A set of computer (special anti-interference computer) 9. A color inkjet printer (HP brand)
10. National first-level metrological identification and quality inspection 11. Product operation manual 12. Certificate of conformity
Complete machine composition:
Step-up part: the step-up part of 0~50KV is composed of voltage regulator and high-voltage transformer. Moving parts: the voltage regulator is uniformly adjusted by the stepping motor to change the voltage applied to the high-voltage transformer. Detection component: measuring circuit composed of integrated circuits. The detected analog signal and switch signal are transmitted to the computer through the signal line. Computer software: transmit the measurement and control signals collected by the detection equipment to the computer through the intelligent circuit. The computer controls the equipment operation and processes the test results according to the collected information. Test electrode: according to the national standard (1408.1-2006), three electrodes are provided with the equipment, and the specific specifications are: Ф 25mm ? Two 25mm; Ф 75mm ? One 25mm. (except customized)
Switching of AC and DC experiments
1) The high voltage output of this instrument is AC voltage. The DC is obtained by serializing the high-voltage silicon stack in the original circuit, so that the test circuit is a pulsating DC voltage. The realization process is as follows: the silicon pile is already in the high-voltage insulation tower of the high-voltage transformer, and the high-voltage silicon pile is usually short-circuited with a short circuit pole. When DC test is required, take out the short circuit rod and connect the high voltage silicon pile into the test circuit. At this time, the circuit voltage is pulsating DC voltage.
2) Front panel DC AC selection button. The status of this button cannot change the nature of the output voltage of the device. Press this button to connect the DC alarm circuit. Instruct the user that you need to discharge the high-voltage equalizing ball when opening the box door. Turn the discharge rod so that the copper ball at the end of the discharge rod contacts the high-voltage equalizing ball. It is recommended that the user contact the high voltage equalizing ball for more than five seconds each time.
3) The AC/DC voltage switching of the test mainly depends on whether the short circuit pole in the high-voltage insulation tower is taken out. When the short-circuit bar is taken out, the voltage on the high-voltage equalizing ball is DC voltage; when the short-circuit bar is inserted, the voltage on the high-voltage equalizing ball is AC voltage. Refer to the schematic diagram on the left for the removal and insertion of the short circuit rod.
matters needing attention:
This instrument is a high-voltage test equipment. The following points must be noted when using it
1. The instrument shall be installed with independent grounding wire.
2. Before starting the machine, the operator should first be familiar with the operation method.
3. The instrument cannot be used in the gas environment with strong corrosive gas and particulate impurities.
4. The test ambient temperature is between 15 ℃ and 25 ℃, and the relative humidity is between 60% and 70%
5. It is normal for the sample to have sparks and sound at the moment of breakdown.
6. Each time the sample is replaced or the high-voltage electrode is contacted, the high-voltage electrode must be discharged with a high-voltage discharge rod for more than 5 seconds.
7. Before each test, the instrument grounding must be checked.
儀器特點:
01、本儀器在試驗過程中可對升壓擊穿過程繪制實時曲線,
02、可以隨時調取當前及歷史試驗數據進行查看,編輯及修改參數。
03、試驗過程中可以隨時修改試驗條件及存儲路徑及自動存儲試驗結果。
04、試驗過程中,可隨時通過軟件決定本次試驗是否有效,方便篩選試驗結果。
05、可設置操作口令,做到專機專人操作,避免無關人員誤操作。
主要產品有:
拉力試驗機, 塑料球壓痕硬度計
維卡熱變形試驗儀, 體積表面電阻率測試儀
海綿泡沫落球回彈試驗機, 海綿泡沫拉伸強度試驗機
耐壓試驗機, 介電常數測試儀
海綿泡沫壓陷硬度測驗儀, 介質損耗測試儀
海綿泡沫切割機, 啞鈴制樣機
海綿泡沫疲勞壓陷試驗機, 薄膜沖擊試驗機
熔融指數儀, 無轉子硫化儀
電壓擊穿試驗儀, 摩擦系數儀
低溫脆性沖擊試驗儀 阿克隆磨耗試驗機等。
業務咨詢:932174181 媒體合作:2279387437 24小時服務熱線:15136468001 盤古機械網 - 全面、科學的機械行業免費發布信息網站 Copyright 2017 PGJXO.COM 豫ICP備12019803號