微機控制門尼粘度試驗機  微機控制，數據顯示，自動校準，

橡膠工業及科研單位理想的實驗儀器。

Adopting imported intelligent digital temperature control instruments, it is easy to adjust and set, and has a wide temperature control range.

The microcomputer adopts imported chips,

High reliability,

All data can be automatically plotted, calculated, and printed.

微機控制門尼粘度試驗機  測試報告

測試報告應包括以下內容；

A樣品描述：

1樣品及其來源的詳細說明；

2從樣品上制備試樣的方法，例如：裁切或邊輥；

B測試方法：

1本部分名稱及編號；

2使用的測試程序；

3使用的試樣類型；

B Test method:

1. Name and number of this section;

2. The testing program used;

3. Type of specimen used;

C測試描述：

1測試前的調節溫度和時間；

2轉子尺寸（大轉子或小轉子）

3測試溫度和相對溫度，如果要求；

4預熱時間（如果不是1小時）；

5測試時間；

6模腔閉合力（如果不是11-5KN）；

7使用的熱穩定薄膜，包括薄膜的厚度；

8詳細說明任何與本部分中規定步驟不同一處；

D測試結果：

1門尼黏度測試結果；

2如果測試試樣多于一個；

  試樣數量；

  單個的測試結果；

  測試結果的平均值（如果測試試樣多于一個）；

E測試日期。

符合標準：GB/T 1232《未硫化橡膠門尼粘度的測定》、GB/T1233《橡膠膠料初期硫化特性的測定 門尼粘度計法》及ISO289、ISO667等標準的要求。

技術參數：

※本參數僅供參考，如有改動恕不另行通知，以公司產品實物為準。

A電源540*660*1100mm

B外型尺寸540*660*1100mm

C重量210kg

D轉子轉速2?0.02r/min

E門尼值測量準確度?0.001個門尼值

F溫度調節范圍室溫--200℃

G模腔溫度波動?0.5℃

H門尼值測量范圍滿量程200個門尼值

I門尼值分辨率0.001個門尼值

E Test date.

Compliance with standards: GB/T 1232 "Determination of Mooney viscosity of uncured rubber", GB/T 1233 "Determination of initial vulcanization characteristics of rubber compounds Mooney viscometer method", and ISO289, ISO667 and other standards.

采用進口智能數字式溫控儀表，調整設定簡便，控溫范圍寬。

微機采用進口芯片，

可靠性高，

全部數據可自動繪圖計算、打印。

Microcomputer control, data display, automatic calibration,

Ideal experimental equipment for rubber industry and research institutions.

Test report

The test report should include the following content;

Sample description:

A detailed description of the sample and its source;

2. Method of preparing samples from samples, such as cutting or edge rolling;

C Test Description:

1. Adjust the temperature and time before testing;

2 rotor size (large or small rotor)

3. Test temperature and relative temperature, if required;

4 preheating time (if not 1 hour);

5 Test time;

6 mold cavity closing force (if not 11-5KN);

7. The thermal stable film used, including the thickness of the film;

8. Provide a detailed explanation of any differences from the steps specified in this section;

D test results:

1. Mooney viscosity test results;

If there is more than one test sample;

Number of samples;

Individual test results;

The average value of the test results (if there is more than one test sample);

Technical parameters:

※This parameter is for reference only and is subject to change without prior notice. The actual product of the company shall prevail.

A power supply 540 * 660 * 1100mm

B Overall size 540 * 660 * 1100mm

C Weight 210kg

D rotor speed 2?0.02r/min

E Mooney value measurement accuracy?0.001 Mooney values

F temperature adjustment range: room temperature -200℃

Temperature fluctuation of G mold cavity?0.5℃

H Mooney value measurement range: 200 Mooney values in full scale

I Mooney value resolution 0.001 Mooney values