注射用水總有機碳分析儀  電源要求

電壓：220V ? 22V

電源頻率：50Hz ? 1Hz

注射用水總有機碳分析儀 應用領域：

    制藥用水（純化水、注射用水）的在線監測和實驗室測試，以及清潔驗證；

環保測試、電子行業、食品行業等。

使用與操作方法

開始檢測并計入檢測次數，檢測完畢后顯示最后一次檢測結果，其中幾次檢測的結果均自動保存在查詢記錄當中。檢測次數的設置方式為：用“選擇”鍵移動光標，用“設置”鍵修改數字，按“確定”鍵進行確認，進入分析界面。先進行四次沖洗過程

在線分析

將TOC 分析儀安置于純水系統的支管或出水管處，對特定點進行實時、連續、在

線監測。在線檢測可方便對水系統的質量進行實時測定并可以對水系統進行實時流程

控制，同時可以在第一時間發現水系統的故障。

運行要求

? 交流電源：170～260 V，頻率：50/60 Hz ；

? 分析儀的量程是：電導率< 10.0 us/cm ；TOC < 1.0 PPM 。如果水樣中的無

機碳或有機碳濃度超出了儀器的檢測范圍，需使用高純水或有機碳濃度較

低的去離子水沖洗管路。

? 儀器運行的環境溫度5℃ – 40 ℃。

安全措施忠告：

1．請保證電源可靠接地；

2．電源電纜線的線徑 > 2.5 mm2；

3．請勿將儀器浸泡于水或其它液體中。

主要技術參數

A. 基本尺寸：44cm?18cm?26cm

B. 檢測極限：0.001mg/L

C. 檢測精度：?5%

D. 檢測范圍：0.001mg/L～1.000mg/L

E. 響應時間：15 min以內

F. 樣品溫度：1-95℃

G. 電   源：220V?22V

H. 電源頻率：50Hz?1Hz

I. 額定功率：100W

J. 分析時間：4min

K. 環境溫度：10-40℃    溫度變化在?5℃/d以內

L. 內部樣品流速：0.5 ml/min

M. 相對濕度：≤ 85%

N. 重復性誤差：≤ 3%

O. 零點漂移：?5%

P. 量程漂移：?5%

工作原理

本儀器采用紫外氧化的原理，將樣品中的有機物氧化為二氧化碳，二氧化碳的測試采用的是直接電導率法，通過測試經過氧化反應的樣品的總碳含量和未經過氧化反應的樣品總無機碳的含量差值來測定總有機碳含量，即：總有機碳（TOC）=總碳（TC）-總無機碳（TIC）。

應用范圍

該儀器可用于檢測制藥工業中純化水、注射用水和去離子水中有機碳的濃度；也可用于半導體行業中超純水TOC的檢測。

在制藥領域和生物化學領域清潔驗證過程中，可用于驗證清潔效果。

該儀器具有在線檢測功能，可以在線監測制藥工業的制水系統、半導體工業的超純水制備系統和晶片工藝過程、電廠去離子水制備過程等。

儀器各部件的安裝、連接

開箱后，按以下步驟進行安裝：

── 根據裝箱單檢查儀器是否齊備。

── 確定儀器在運輸過程中沒有遭到損壞。

── 拆除機箱的外包裝，將其置于正確位置 。

── 檢查儀器保險絲是否裝好，連接市電電纜到接線端子。

── 根據安裝圖連接進液和出液管路 。

── 系統通電 。

產品特點

1.儀器采用便攜設計，使用輕便，方便移動至取樣點。

2.采用嵌入式系統，觸摸屏設計，純中文操作方便簡易。

3.針對制藥用水（TOC含量在1000ppb以下）總有機碳含量的檢測設計，進行檢測。

4.配備大量的儲存空間，能夠存儲大量的測試數據。

5.中文打印，輸出測試參數、測試結果。

6.在使用、貯存和更換過程中不需要氣體或試劑，無移動部件，減少維修和維護成本。

7.當測試樣品濃度超過規定限度，儀器能夠自動報警，并輸出控制信號。

8.符合國家2010版《中國藥典》規定的測試方案，可以提供IQ/OQ/PQ服務。

Power requirements

Voltage: 220V?22V

Power frequency: 50Hz?1Hz

Application field:

Online monitoring and laboratory testing of pharmaceutical water (purified water, injection water), as well as cleaning validation;

Environmental testing, electronics industry, food industry, etc.

Usage and operation methods

Start the detection and count the number of detections. After the detection is completed, the last detection result will be displayed, and the results of several detections will be automatically saved in the query record. The way to set the number of detections is to use the "Select" key to move the cursor, use the "Set" key to modify the number, press the "OK" key to confirm, and enter the analysis interface. Perform four flushing processes first

Online analysis

Place the TOC analyzer at the branch or outlet pipe of the pure water system, and perform real-time, continuous, and accurate monitoring of specific points

Line monitoring. Online detection facilitates real-time measurement of the quality of the water system and enables real-time flow control of the water system

Control, and at the same time, detect faults in the water system as soon as possible.

Operational requirements

AC power supply: 170-260 V, frequency: 50/60 Hz;

The range of the analyzer is: conductivity<10.0 us/cm; TOC<1.0 PPM. If there is none in the water sample

The concentration of organic carbon or organic carbon exceeds the detection range of the instrument, and high-purity water or organic carbon concentration should be used

Flush the pipeline with low deionized water.

The ambient temperature for instrument operation is 5℃-40℃.

Safety measures and advice:

1. Please ensure reliable grounding of the power supply;

2. The wire diameter of the power cable is>2.5 mm2;

3. Do not immerse the instrument in water or other liquids.

Main technical parameters

A. Basic size: 44cm?18cm?26cm

B. Detection limit: 0.001mg/L

C. Detection accuracy:?5%

D. Detection range: 0.001mg/L~1.000mg/L

E. Response time: Within 15 minutes

F. Sample temperature: 1-95℃

G. Power supply: 220V?22V

H. Power frequency: 50Hz?1Hz

I. Rated power: 100W

J. Analysis time: 4 minutes

K. Environmental temperature: 10-40℃Temperature variation within?5℃/d

L. Internal sample flow rate: 0.5 ml/min

M. Relative humidity:≤85%

N. Repeatability error:≤3%

O. Zero drift:?5%

P. Range drift:?5%

operational principle

This instrument adopts the principle of ultraviolet oxidation to oxidize organic matter in the sample to carbon dioxide. The measurement of carbon dioxide is carried out using the direct conductivity method. The total organic carbon content is determined by measuring the difference between the total carbon content of the sample that has undergone oxidation reaction and the total inorganic carbon content of the sample that has not undergone oxidation reaction. That is, total organic carbon (TOC)=total carbon (TC) - total inorganic carbon (TIC).

Application scope

This instrument can be used to detect the concentration of organic carbon in purified water, injection water, and deionized water in the pharmaceutical industry; It can also be used for the detection of TOC in ultrapure water in the semiconductor industry.

In the cleaning validation process in the pharmaceutical and biochemical fields, it can be used to verify the cleaning effect.

This instrument has an online detection function, which can monitor the water preparation system in the pharmaceutical industry, the ultra pure water preparation system and chip process in the semiconductor industry, and the deionized water preparation process in power plants online.

Installation and connection of various components of the instrument

After unpacking, follow the following steps for installation:

Check if the instruments are complete according to the packing list.

Ensure that the instrument has not been damaged during transportation.

Remove the outer packaging of the chassis and place it in the correct position.

Check if the instrument fuse is installed properly and connect the mains cable to the wiring terminal.

Connect the inlet and outlet pipelines according to the installation diagram.

Power on the system.

Product features

1. The instrument adopts a portable design, which is lightweight and easy to move to the sampling point.

2. Adopting embedded system and touch screen design, pure Chinese operation is convenient and simple.

3. Design and conduct testing for the total organic carbon content of pharmaceutical water (TOC content below 1000ppb).

4. Equipped with a large amount of storage space, capable of storing a large amount of test data.

5. Print in Chinese, output test parameters and test results.

6. No gas or reagents are required during use, storage, and replacement, and there are no moving parts, reducing repair and maintenance costs.

When the concentration of the test sample exceeds the specified limit, the instrument can automatically alarm and output a control signal.

8. According to the testing plan specified in the 2010 edition of the Chinese Pharmacopoeia, IQ/OQ/PQ services can be provided.