韩国精品一区二区三区无码视频,国产午夜福利视频在线观看,永久黄网站色视频免费无下载,色婷婷av一区二区三区浪潮

【請登錄】【免費注冊】

首頁新聞技術產品供應二手培訓展會物流維修求購招商招標招聘企業

供應

搜索
產品信息產品篩選產品類型大全供應信息求購信息二手設備生產銷售企業
您的位置:盤古機械網>供應信息>供應詳情

塑料表面體積電阻率測定儀廠家

價格:38450元瀏覽:38次聯系:劉元元 / 15132636097 / 企業:北京北廣精儀儀器設備有限公司留言店鋪收藏

塑料表面體積電阻率測定儀廠家  技術參數:

1、電阻測量范圍1?104Ω~1?1018Ω

2、電流測量范圍2?10-4A~1?10-16A

3、顯 示 方 式 數字液晶顯示

4、內置測試電壓10V、50V、100V、250V、500V、1000V

5、基本準確度1%

6、使用環境 溫度:0℃~40℃,相對濕度<80%

7、供電形式AC 220V,50HZ,功耗約5W

8、儀器尺寸285mm? 245mm? 120 mm

9、質量約5KG

10、體積小、重量輕、準確度高電阻、電流雙顯示,性能好穩定、讀數方便

11、使測量超高電阻就如用萬用表測量普通電阻樣簡便免去老式高阻計在不同測試電壓下或不同量程時要乘以系數等使用不便的麻煩

塑料薄膜電阻率測定儀既可測量高電阻,又可測微電流。采用了美國Intel公司的大規模集成電路,使儀器體積小、重量輕、準確度高。以雙3.1/2位數字直接顯示電阻的高阻計和電流。量限從1?104Ω~1?1018 Ω,是目前國內測量范圍 寬,準確度 高的數字超高阻測量儀。

塑料表面體積電阻率測定儀廠家  材料說明

 

  A、通常,絕緣材料用于電氣系統的各部件相互絕緣和對地絕緣,固體絕緣材料還起機械支撐作用.一般希望材料有盡可能高的絕緣電阻,并具有合適的機械、化學和耐熱性能.

 

  B、體積電阻班組可作為選擇絕緣材料的一個參數,電阻率隨溫度和濕度的京戲化而顯著變化.體積電阻率的測量常常用來檢查絕緣材料是否均勻,或都用來檢測那些能影響材料質量而又不能作其他方法檢測到的導電雜質.

 

  C、當直流電壓加到與試樣接觸的兩電極間時,通過試樣的電流會指數式地衰減到一個穩定值.電流隨時間的減小可能是由于電介質極化和可動離子位移到電極所致.對于體積電阻小于10的10Ω.m

 

  的材料,其穩定狀態通常在1min內達到.因此,要經過這個電化時間后測定電阻.對于電阻率較高的材料,電流減小的過程可能會持續幾分鐘、幾小時、幾天,因此需要用較長的電化時間.如果需要的話,可用體積電阻率與關系來描述材料的特性.

 

  D、由于體積電阻總是要被或多或少地包括到表面電阻的測試中去,因些近似地測量表面電阻,測得的表面電阻值主要反映被測試樣表面污染的程度.所以,表面電阻率不是表面材料本身特性的參數,而是一個有關材料表面污染特性的參數.

 

  當表面電阻較高時,它常隨時間以不規則的方式變化.測量表面電阻通常都規定11min的電化時間.

 

試樣處置

電極之間或測量電極與大地之間的雜散電流對于測試儀器的讀數沒有明顯的影響這一點很重要。測試時加電極到試樣上和安放試樣時均要極為小心,以免可能產生對測試結果有不良影響的雜散電流通道。

測量表面電阻時,不要清洗表面,除非另有協議或規定。除了同二材料的另一個試樣的未被觸模過的表面可觸及被測試樣外,表面被測部分不應被任何東西觸及。

 

什么是電阻率?

 

  電阻跟導體的材料、橫截面積、長度有關。

 

  導體的電阻與兩端的電壓以及通過導體的電流無關。

 

  導體電阻跟它長度成正比,跟它的橫截面積成反比.

 

  (1)定義或解釋

 

  電阻率是用來表示各種物質電阻特性的物理量。用某種材料制成的長為1米、橫截面積為1mm2米。的導體的電阻,在數值上等于這種材料的、電阻率。

 

  (2)單位

 

  在國際單位制中,電阻率的單位是歐姆?米。一般常用的單位是歐姆?毫米2/米。

 

  (3)說明

 

  ①電阻率ρ不僅和導體的材料有關,還和導體的溫度有關。在溫度變化不大的范圍內,幾乎所有金屬的電阻率隨溫度作線性變化,即ρ=ρo(1 at)。式中t是攝氏溫度,ρo是O℃時的電阻率,a是電阻率溫度系數。

 

 ?、谟捎陔娮杪孰S溫度改變而改變,所以對于某些電器的電阻,必須說明它們所處的物理狀態。如一個220V

 

  100W電燈燈絲的電阻,通電時是484歐姆,未通電時只有40歐姆左右。

 

 ?、垭娮杪屎碗娮枋莾蓚€不同的概念。電阻率是反映物質對電流阻礙作用的屬性,電阻是反映物體對電流阻礙作用的屬性。

 

What is electrical resistivity?

 

Resistance is related to the material, cross-sectional area, and length of the conductor.

 

The resistance of a conductor is independent of the voltage at both ends and the current passing through the conductor.

 

The resistance of a conductor is directly proportional to its length and inversely proportional to its cross-sectional area

 

(1) Definition or Explanation

 

Electrical resistivity is a physical quantity used to represent the resistance characteristics of various substances. Made of a certain material with a length of 1 meter and a cross-sectional area of 1mm2. The resistance of a conductor is numerically equal to the resistivity of this material.

 

(2) Unit

 

In the International System of Units, the unit of electrical resistivity is ohms per meter. The commonly used unit is ohm ? mm2/meter.

 

(3) Explanation

 

① The resistivity ρ is not only related to the material of the conductor, but also to the temperature of the conductor. Within a range where temperature does not change significantly, the resistivity of almost all metals varies linearly with temperature, i.e., ρ=ρ o (1 at). In the formula, t is the temperature in Celsius, ρ o is the resistivity at O ℃, and a is the temperature coefficient of resistivity.

 

② Due to the change in resistivity with temperature, it is necessary to explain the physical state of the resistance of certain electrical appliances. Like a 220V

 

The resistance of a 100W electric lamp filament is 484 ohms when powered on and only about 40 ohms when not powered on.

 

③ Electrical resistivity and resistance are two different concepts. Electrical resistivity is a property that reflects the obstruction of current by a substance, while resistance is a property that reflects the obstruction of current by an object.

 

電極材料

8.1概述

絕緣材料用的電極材料應是一類容易加到試樣上、能與試樣表面緊密接觸、且不致于因電極電阻或對試樣的污染而引入很大誤差的導電材料。在試驗條件下,電極材料應能耐腐蝕。下面是可使用的一些典型的電極材料。電極應與給定形狀和尺寸的合適的背襯電極一同使用。

簡便的做法是用兩種不同的電極材料或兩種不同的使用方法來了解電極材料是否會引人很大誤差。

8.2導電銀漆

某些高導電率的商品銀漆,無論是氣干的或低溫烘干的,是足夠疏松的、能透過溫氣,因此可在加上電極后對試樣進行條件處理。這種特點特別適合研究電阻濕氣效應以及電阻隨溫度的變化。然而,在導電漆被用作一種電極材料以前,應證實漆中的潛劑不影響試樣的電性能。用精巧的毛刷可做到使保護電極的邊緣相當光滑。但對于圓電極,可先用圓規畫出電極的輪廊,然后用刷子來涂滿內部的方法來獲得精細的邊緣。如電極漆是用噴槍噴上去的,則可采用固定模框。

8.3噴鍍金屬

可使用能滿意地粘合在試樣上的噴鍍金屬。薄的噴鍍電極的優點是一旦噴在試樣上便可立即使用。這種電極或許是足夠疏松的,可允許對試樣進行條件處理,但這→特點應被證實。固定的模框可用 來制取被保護電極與保護電極之間的間隙。

8.4蒸發或陰極真空噴鍍金屬

當能證明材料不受離子轟擊或真空處理的影響時,蒸發或陰極真空噴鍍金屬能在與8. 3給出的相同條件下使用。

8.5液體電極

使用液體電極往往能得到滿意的結果。構成上電極的液體應被框住,例如用不銹鋼環來框住,每個環的下邊緣在不接觸液體的一面被斜削成銳邊。圖4給出了使用液體電極的裝置。 不推薦長期使用或 在高溫下使用水銀,因為它有毒。

8.6膠體石墨

分散在水中或其他合適媒質中的肢體石墨可在與8. 2給出的相同條件下使用。

8. 7導電橡皮

導電橡皮可用作電極材料。它的優點是能方便快捷地放上和移開。由于只是在測定時才將電極放到試祥上,因此它不妨礙試樣的條件處理。導電橡皮應足夠柔軟,以確保其在加上適當的壓力例如2 kPa(O. 2 N/cm2)時能與試樣緊密接觸。

8.8金屬錨

金屬錨可粘貼在試樣表面作為測量體積電阻用的電極,但它不適用于測量表面電阻。鉛、錦鉛合金、鋁和錫錨都是被普遍使用的。通常用少量的凡士林、硅脂、硅油或其他合適的材料作為粘貼劑將它們粘貼到試樣上去。含有下列組分的一種藥用膠適合用作導電粘貼劑:

分子量為600的無水聚乙二醇800份(質量)

水200份(質量)

軟肥皂(藥用級)1份(質量)

氧化鉀

要在一個平穩的壓力下粘貼電極,使之足以消除一切皺折和將多余的粘合劑趕到筒的邊緣,再用一塊干凈的薄紙擦去。用軟物如手指按壓能很好地做到這點。這個技巧僅適用于表面非常平滑的試樣。通過精心操作,粘合劑薄層可減小到0. 002 5 mm或更薄。

Electrode material

8.1 Overview

The electrode material used for insulation materials should be a conductive material that is easy to apply to the sample, can be in close contact with the sample surface, and does not introduce significant errors due to electrode resistance or contamination of the sample. Under experimental conditions, the electrode material should be corrosion-resistant. Here are some typical electrode materials that can be used. The electrode should be used with a suitable backing electrode of the given shape and size.

A simple approach is to use two different electrode materials or two different usage methods to determine whether the electrode material will introduce significant errors.

8.2 Conductive Silver Paint

Some high conductivity silver paints, whether air dried or low-temperature dried, are sufficiently loose and can pass through warm air, so they can be conditioned on the sample after adding electrodes. This characteristic is particularly suitable for studying the moisture effect of resistance and the variation of resistance with temperature. However, before using conductive paint as an electrode material, it should be confirmed that the latent agent in the paint does not affect the electrical properties of the sample. Using a delicate brush can make the edges of the protective electrode quite smooth. But for circular electrodes, you can first draw the contour of the electrode with a compass, and then use a brush to coat the inside to obtain fine edges. If the electrode paint is sprayed with a spray gun, a fixed mold frame can be used.

8.3 Metal spraying

Spray metal that can be satisfactorily adhered to the sample can be used. The advantage of thin spray coated electrodes is that they can be used immediately once sprayed onto the sample. This type of electrode may be loose enough to allow for conditioning of the sample, but this characteristic should be confirmed. A fixed mold frame can be used to create a gap between the protected electrode and the protective electrode.

8.4 Evaporation or cathodic vacuum deposition of metals

When it can be proven that the material is not affected by ion bombardment or vacuum treatment, evaporation or cathodic vacuum deposition of metals can be compared to 8 Use under the same conditions as given in 3.

8.5 Liquid electrode

The use of liquid electrodes often yields satisfactory results. The liquid that constitutes the upper electrode should be framed, for example, with stainless steel rings, and the lower edge of each ring should be chamfered to a sharp edge on the side that does not come into contact with the liquid. Figure 4 shows the device using liquid electrodes. It is not recommended to use mercury for a long time or at high temperatures because it is toxic.

8.6 Colloidal graphite

Limb graphite dispersed in water or other suitable media can be used in conjunction with 8 Use under the same conditions as given in 2.

8.7 Conductive rubber

Conductive rubber can be used as electrode material. Its advantage is that it can be easily and quickly placed on and removed. Since the electrode is only placed on the test sample during the measurement, it does not hinder the conditioning of the sample. The conductive rubber should be soft enough to ensure close contact with the sample when subjected to appropriate pressure, such as 2 kPa (0.2 N/cm2).

8.8 Metal Anchor

Metal anchors can be attached to the surface of the specimen as electrodes for measuring volume resistance, but they are not suitable for measuring surface resistance. Lead, lead alloy, aluminum, and tin anchors are commonly used. Usually, a small amount of Vaseline, silicone grease, silicone oil, or other suitable materials are used as adhesives to stick them to the sample. A medicinal adhesive containing the following components is suitable for use as a conductive adhesive:

800 parts (mass) of anhydrous polyethylene glycol with a molecular weight of 600

200 parts of water (by quality)

1 serving of soft soap (medicinal grade) (quality)

Potassium oxide

To paste the electrode under a steady pressure, it is necessary to eliminate all wrinkles and push excess adhesive to the edge of the cylinder, and then wipe it off with a clean thin paper. Pressing with soft objects such as fingers can achieve this very well. This technique is only applicable to samples with very smooth surfaces. Through careful operation, the thin layer of adhesive can be reduced to 0 002 5mm or thinner.

符合標準

GB/T 1410-2006、GB 12014、GB/T 20991-2007、GB 4385-1995、GB 12158-2006、GB 4655-2003、GB/T 12703.4-2010、GB/T 12703.6-2010、GB 13348-2009、GB/T 15738-2008、GB/T 18044-2008、GB/T 18864-2002、GB/T 22042-2008、GB/T 22043-2008、GB/T 24249-2009、GB 26539-2011、GB/T 26825-2011、GB 50515-2010、GB 50611-2010、GJB 105-1998-Z、GJB 3007A-2009、GJB 5104-2004

標準配置:

 1、儀器主機 一臺

 2、屏蔽箱一個

 3、試驗電極三個

 4、說明書一本

 5、電源線一條

 6、數據線三條

 7、合格證一份

 8、保修卡一份

體積電阻率與表面電阻的區別

 

體積電阻率和表面電阻是材料電學性能的兩個重要參數,但兩者針對的測試對象和應用場景不同。以下是兩者的主要區別:

 

 

1. 定義與物理意義

體積電阻率(Volume Resistivity)  

  體積電阻率是衡量材料內部導電性能的參數,表示單位體積材料對電流的阻礙能力。 

 

 

  體積電阻率反映材料本身的絕緣或導電特性,與材料的成分、結構及溫度密切相關。例如,絕緣塑料的 可達12次方-16次方,而金屬的 僅為  10的-6}- 10^-4次方 。

 

表面電阻(Surface Resistance)  

  表面電阻是衡量材料表面導電性能的參數,表示電流沿材料表面流動時的阻礙能力。 

 

 

  表面電阻受材料表面狀態(如污染、濕度、氧化層)影響顯著,常用于評估材料的防靜電性能或漏電風險。

 

2. 測量方法與電極配置

-體積電阻率測量  

  - 電極設計:使用三電極系統(如保護環電極),確保電流僅通過材料內部,避免表面電流干擾。  

  - 測試標準:如 ASTM D257、IEC 60093。  

  - 適用場景:塊狀固體材料(如塑料、陶瓷、橡膠)的絕緣性能評估。

 

- 表面電阻測量

  -電極設計:采用平行電極或同心環電極,使電流沿材料表面流動。  

  -測試標準:如 ASTM D4496、IEC 61340。  

  -適用場景:薄膜、涂層、紡織品等表面導電性能測試,或防靜電材料的篩選。

 

 

3. 應用領域差異

參數     

體積電阻率:                                        

核心用途評估材料內部絕緣

典型應用電線絕緣層、電子封裝材料、高壓設備

關鍵影響因素材料成分、溫度、雜質濃度

 

表面電阻:評估材料表面導電/防靜電性能 導電性

 

影響因素表面清潔度、濕度、污染、氧化層  

 

4. 實例對比

絕緣塑料板: 

  體積電阻率高于15次方,說明內部絕緣性能優異;  

  - 表面電阻可能因吸附水分而降低于12次方,表明表面存在微弱導電性。  

 

5. 總結

體積電阻率:表征材料整體的絕緣或導電能力,是材料本征屬性的體現。 

表面電阻:反映材料表面的導電特性,易受環境因素和表面狀態影響。 

 

兩者在科研、工業質檢中常需同時測試,以全面評估材料的電學性能(如高壓絕緣材料需高體積電阻率 高表面電阻,而防靜電材料需中等體積電阻率 低表面電阻)。

 

此會員其它供應

業務咨詢:932174181   媒體合作:2279387437    24小時服務熱線:15136468001 盤古機械網 - 全面、科學的機械行業免費發布信息網站 Copyright 2017 PGJXO.COM 豫ICP備12019803號

主站蜘蛛池模板: 国产人妻无码一区无| 国产精品亚洲а∨天堂网不卡| 国产亚洲无日韩乱码| 香蕉在线 亚洲 欧美 专区| 国产电影无码午夜在线播放| 国产精品久久| 国产精品亚洲а∨无码播放不卡| 中文字幕人妻被公上司喝醉506| 黄页网站18以下勿看| 精品成人一区二区三区四区| 欧美人与动牲猛交xxxxbbbb| 久久久久亚洲av无码专区首| 亚洲精品无码永久在线观看男男| 国产婷婷丁香五月缴情成人网| 国产成人av乱码免费观看| 久久精品免费观看国产| 日本丰满少妇裸体自慰| 4480yy私人精品国产| 国产成人一卡2卡3卡4卡| 亚洲国产av玩弄放荡人妇系列| 人妻少妇无码精品专区| 无码视频一区二区三区| 免费国产午夜视频在线| 人人澡人人澡人人看添av| 国产亚洲欧美日韩夜色凹凸成人| 精品少妇一区二区三区视频| 97色精品视频在线观看| 国产成人精品日本亚洲专区61| 性做久久久久久| 热久久国产欧美一区二区精品| 午夜成人福利片无码| 久久亚洲精品综合国产仙踪林| 日本无卡码高清免费v| 亚洲人成人77777网站| 一区二区狠狠色丁香久久婷婷| 妺妺窝人体色www在线小说| 久久九九av免费精品| 无码专区一ⅴa亚洲v专区在线| 国产精品久久久一区二区三区| 国产美女极度色诱视频www| 久久99精品国产麻豆蜜芽|