德國GT-550脈沖式探測器是一款抗高壓，大深度脈沖式金屬探測器，主用于寶藏、遺址、考古。探測深度可達十米，一個30公分法人銅片現場實際探測達3.5米。

產品用途：考古、探寶、金、銀、銅等。






GT550是一款采用德國KTS技術原裝芯片，大深度脈沖機，它比傳統的脈沖機器更深更穩定，抗高壓。且操作方法特別簡單。
操作方法：開關：開機旋鈕和音量大小功率：機器功率大小調節 功率越大深度越大 反之越?。ň唧w深度需要靈敏度和復位按鈕來配合調節）
高壓檔位：（深度好但是受到的干擾也越大）
普通檔位： 適合干擾嚴重和有礦化的地方使用，但是深度不如高壓擋具體使用檔位根據實地干擾和土質決定（如遇高壓線打到此檔位）
Sing:信號指示.led燈與顯示屏信號同步 探測到金屬紅燈亮
頻率：輔助機器旋鈕也叫敏感度 一般調節到一秒響二三下為宜
靈敏度：深度控制旋鈕 調節到比敏感度快一點點 探測時始終保持此狀態（深度才會好）
 Phones:耳機插孔 插上耳機 外音自動斷開



注意事項：機器操作時 保持關機狀態  插上線圈然后開機  測試效果可以線圈放在地面 實際操作時需要保持線圈離地面30厘米高度調節機器 然后進行探測，探測深度根據被測物體大小深度不同。30公分小線圈盤以一個銅錢為例 深度50公分。1米框以30公分金屬為例  2-2.5米（實埋）2米框以30公分金屬為例  3-3.5米(實埋)被測物體越大線圈框越大探測深度越深。
功率300W  
電池16.8V  
6000毫安
頻率600Hz




產品特點：
1.探測深度： 12米
2.探測范圍大：搜索完1個足球場只需40分鐘
3.地平衡比較穩定：探測時不受礦化反應和鹽類物質的影響

4.它配備多種搜索線圈，可適應各種不同探測需要

The German GT-550 pulse detector is a high-voltage resistant, large-depth pulsed metal detector, mainly used for treasures, ruins, and archaeology. The detection depth can reach ten meters, and the actual detection of a 30 cm corporate copper sheet on site can reach 3.5 meters.
Product use: archaeology, treasure hunting, gold, silver, copper, etc.
GT550 is a large depth pulse machine with original German KTS technology. It is deeper and more stable than traditional pulse machines, and is resistant to high voltage. And the operation method is particularly simple.
Operation method: switch: turn on the knob and volume power: adjust the power of the machine, the greater the power, the greater the depth, the smaller it is (the specific depth requires sensitivity and reset buttons to adjust)
High pressure gear: (the depth is good but the interference is greater)
Ordinary gear: suitable for use in places with severe interference and mineralization, but the depth is not as good as the high-voltage gear. The specific gear used is determined according to the field interference and soil quality (if high-voltage lines hit this gear)
Sing: Signal indication. The led light is synchronized with the display signal, the red light is on when the metal is detected
Frequency: The auxiliary machine knob is also called sensitivity. It is generally appropriate to adjust to two or three times per second.
Sensitivity: The depth control knob is adjusted to be a little faster than the sensitivity. Always maintain this state during detection (the depth will be good)